Admin
مدير المنتدى
عدد المساهمات : 18726
التقييم : 34712
تاريخ التسجيل : 01/07/2009
الدولة : مصر
العمل : مدير منتدى هندسة الإنتاج والتصميم الميكانيكى
 |  موضوع: كتاب Practical Guide to Rubber Injection Moulding الأربعاء 04 سبتمبر 2019, 11:19 pm | |
| 
أخوانى فى الله
أحضرت لكم كتاب
Practical Guide to Rubber Injection Moulding
John A. Lindsay
و المحتوى كما يلي :
Contents
Preface ix
1 Market Leader: Introduction . 1
1.1 Perfection of the Process 1
1.2 Historical Background . 1
1.2.1 Practical Considerations 2
Reference . 4
2 Setting the Parameters: Initial Stages . 5
2.1 The Quality System . 5
2.2 Shape . 5
2.3 Polymer Compatibility . 5
2.4 Production Volume 6
2.5 Start of Production 6
2.6 Component Design 6
2.6.1 The Enquiry Stage . 6
2.6.2 Finalising the Component Shape . 7
2.6.3 Compound Design 7
2.6.3.1 Oils and Solvents 7
2.6.3.2 Gases 8
2.6.3.3 Water 8
2.6.3.4 Temperature . 8
2.6.4 Engineering Requirements . 8
2.6.4.1 Resilience or Damping 8
2.6.4.2 Fatigue Resistance 9
References . 9
Contents iv
Practical Guide to Rubber Injection Moulding
3 The Rubber Compound . 11
3.1 Specification 11
3.2 Selection of Polymer 11
3.3 Hardness or Modulus 12
3.4 Compound Design and Cost 12
3.5 Factors that Adversely Affect Processing 12
3.5.1 Scorch . 12
3.5.2 Effect of Temperature 14
3.5.3 Compound Viscosity . 15
3.5.4 Moisture . 18
3.5.5 Gel 18
3.6 Mixing . 18
3.6.1 Weighing of Ingredients . 18
3.6.2 Mixing Cycles . 19
3.7 Compounding Ingredients . 20
3.7.1 Polymers . 20
3.7.1.1 Natural Rubber . 20
3.7.1.2 Synthetic Polymers . 21
3.7.1.3 Peptisers 21
3.7.1.4 Zinc Oxide 21
3.7.1.5 Stearic Acid and Activation . 22
3.7.1.6 Fillers . 22
3.7.1.7 Process Aids . 23
3.7.1.8 Process Oils . 23
3.7.1.9 Accelerators . 23
3.7.1.10 Sulfur . 24
3.7.1.11 Anti-ozonants 24
3.7.1.12 Masterbatching of Compounds . 24
3.7.2 Characterisation of Materials 24
3.7.3 Example Compound Formulations . 24
3.8 Stock Presentation . 25
3.9 Storage of Uncured Rubber . 26
References . 26v
Contents
4 The Injection Machine . 27
4.1 The Parts to Understand 27
4.2 The Pre-plasticising and Injection Unit 27
4.3 The Press Unit . 31
4.3.1 Horizontal or Vertical Opening? . 32
4.3.2 Hydraulic or Toggle Clamp? . 32
4.4 Hydraulic Power 33
4.4.1 Oil Cooling . 33
4.4.2 Clean Oil 33
4.5 Heating and Cooling . 34
4.5.1 Platen Heating 34
4.5.2 Cavity Temperature . 35
4.6 Control Systems . 35
Reference . 36
5 Mould Design 37
5.1 Sizing of Moulds 37
5.2 Runner System . 38
5.2.1 The Sprue Bush . 40
5.2.2 Injection Gates 40
5.3 Air Removal 41
5.4 Modelling Software . 42
5.5 Ejector Systems 42
5.6 Flashless Mouldings . 42
5.7 Mould Monitoring Points 43
5.8 Mould Materials 43
References . 45
6 Moulding 47
6.1 Purging 47
6.2 Single Cavity Tools 48
6.3 Initial Process Set-up 48
6.4 Problem Solving . 51vi
Practical Guide to Rubber Injection Moulding
6.4.1 Recognition . 51
6.4.2 Classifying the Fault 51
6.4.3 Identifying Causes . 51
7 Mould Fouling, Cleaning and Management 55
7.1 Mould Management 57
7.2 Platen Condition 57
8 Mould Release Agents . 59
8.1 Sacrificial Mould Release Agents . 59
8.2 Internal Mould Release Agents 60
8.3 Semi-permanent Mould Release Agents . 60
8.4 Method of Application 60
9 Maintenance 63
9.1 Routine Matters 63
9.2 Routine Maintenance 64
9.3 New Job Start-up Procedures . 64
9.4 Reworking . 65
10 Bonding of Rubber to Substrates . 67
10.1 Introduction 67
10.2 Compound 67
10.2.1 Polymer . 67
10.2.2 Curing System . 68
10.2.3 Rubber Presentation at the Press . 68
10.3 Inserts 68
10.3.1 Condition 68
10.3.2 Metal Inserts . 68
10.3.3 Plastic Inserts 69
10.4 Insert Preparation 70
10.4.1 Solvent Degreasing 70
10.4.2 Aqueous Degreasing 71vii
Contents
10.5 Surface Preparation . 71
10.5.1 Grit Blasting 72
10.5.2 Wet Processes 73
10.6 Bonding Systems 73
10.6.1 Control of the Bonding Agent . 75
10.6.2 Application Methods 75
10.6.3 Storage and Handling of Prepared Inserts . 76
10.7 Moulding . 76
10.7.1 Preheating the Inserts 76
10.7.2 The injection Cycle . 77
Appendix 1 . 79
Appendix 2 . 85
Appendix 3 . 89
Appendix 4 . 93
Appendix 5 . 95
Appendix 6 . 97
Appendix 7 . 99
Appendix 8 . 101
Abbreviations 103
Index . 105
كلمة سر فك الضغط : books-world.net
The Unzip Password : books-world.net
أتمنى أن تستفيدوا من محتوى الموضوع وأن ينال إعجابكم
رابط من موقع عالم الكتب لتنزيل كتاب Practical Guide to Rubber Injection Moulding
رابط مباشر لتنزيل كتاب Practical Guide to Rubber Injection Moulding
|
|
